Contact Us

2" (50mm) binding strap

Length: 30' (9,14m)

Winch

A device that attaches to the bolt of the panel, used to straighten walls and hold them firmly in place while the concrete is being poured. Simple and sturdy, this winch comes with a 30 foot (9m) strap.

Binder strap with hook

Securely binds the material to the truck.

Screws, bolts, sleeves

Spare parts.

Anchor bolt

8" (200mm) x 1/2" (12,5mm) anchor bolt with bolts and washers.

Wall straightener with 2" x 4" (50mm x 100mm) clamp

This easy to use 5/16" (8mm) tool attaches to the bolt of the panel and allows you to slide in a vertical 2" x 4" (50mm x 100mm) or 2" x 6" (50mm x 150mm) lumber at the desired height. You can then straighten the wall by tightening the clamp on the lumber.

Wall straightener with 4" x 8" (100mm x 200mm) clamp

Helps straighten a wall of panels by tightening the screw on the 2" x 4" (50mm x 100mm).

Head aligner with clamp

Used to rectify and solidify the alignment of part of the formwork.

Head aligner with tip

Steel piece used to straighten and align the panel heads in order to obtain a straight concrete surface.

This tool attaches to the top of the panel on the inside and outside. You can then slide a 2" x 4" (50mm x 100mm) behind the tip on the outside of the wall and, using a hammer, tighten the 2" x 4" (50mm x 100mm) between the tip and the panel.

Loop wires

Strong and flexible, these are perfect for attaching steel reinforcement.

Come in practical 2,500-piece rolls.

Standard lengths available: 4" (100mm), 6" (150mm) and 8" (200mm).

Automatic and manual wire fastener

Tool used to twist wire.

Metal chimney

Quickly fastens to the inside of the formwork for attractive and quality installation.

1/8" (3mm) steel (heat resistant, recommended by authorities in the field, etc.).

Depth can be adjusted from 8" to 10" (200mm x 250mm).

Compatible with all formwork systems of this type.

Waterstop

Makes a watertight seal between the footing and foundation wall.

50' (15,25m) or 100' (30,5m) rolls (standard size).

Waterstop welder

Tool used to weld waterstops.

Very Sturdy Shovels

Shovels of different shapes and lengths for laying concrete.

Aluminum concrete scooper

Helps evenly spread the concrete of the footings for a nice finish.

Aluminum concrete spreader

Helps evenly spread the concrete on slabs and footings.

Aluminum rake

Used to spread the cement over the desired surface.

Trowel

Allows you to have a nice finish by flattening the concrete surface.

Scraper

To better clean the panels.

Chalk line 100' (30,5m)

Makes a straight line using chalk as a reference.

Chalk line 150' (45,7m)

Makes a straight line using chalk as a reference.

Marking powder

Marking powder of excellent quality.

Choice of colours / 5 lbs (2,27 kilos).

Paint diffuser

Mark the floor without having to bend down.

Bending machine

Can bend and cut reinforcing rods up to 5/8" (16mm) in diameter.

Set to the desired degree.

Corner remover

Tool that makes it much easier to remove corners and can be used to remove panels too.

Panel remover

Tool that makes it much easier to remove panels.

"H" panel support

For overlapping a panel over another panel.

"H" beam support

For placing a beam over the panels.

Swing corner lock

For adjustment and to hold an adjustable corner at the desired angle if needed.

Morin bracket

Bracket to overlap a panel over another with tie and nails.

Stacking plate

Firmly holds the stacked panels. The notch in the plate keeps the tie from moving, providing alignment and stability.

Line clip

Quickly and solidly attaches a rope to the drop of the panel to align the wall. Prevents you from having to nail the top of the panel, thus increasing its service life.

Heavy duty crane hook

Used to pick up formwork cages.

Allows the crane operator to work alone.

Balcony support

Allows you to obtain the desired surface size while the form provides support for the balcony.

Adjustable shoring post

Adjustable post to help push or pull a wall.

Beam with straps

To release multiple panels without unlocking them.

Laser support

A steady support for the laser.

Fixes itself to a corner or a panel.

Most stable when attached to a corner.

Bucket beam

Creates a space to sit the column / beam on. The angled corners facilitate its removal.

Chimney circle

Allows you to form a circular empty space in the concrete for the chimney pipe to pass through.

Easy to remove.